100 |
communication not configured |
[OK], [ON] |
Reconfigure slave IPC |
[OFF] |
Cancel embossing. |
101 |
communication timeout |
[OK], [ON] |
No Action. |
[OFF] |
Cancel embossing. |
102 |
restart communication |
[OK], [ON] |
Reset slave. |
[OFF] |
Cancel embossing. |
104 |
reset printing queue |
[OK], [ON] |
Clear print queue and reset slave. |
[OFF] |
Cancel embossing. |
120 |
Out of paper |
[OK], [ON] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[OFF] |
Cancel embossing. |
121 |
Paper jam |
[OK], [ON] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[OFF] |
Cancel embossing. |
[1] |
Turn off paper jam sensor and continue printing |
122 |
Paper length fail |
[OK], [ON] |
No action. |
[OFF] |
Cancel embossing. |
123 |
Paper feed failed |
[OK] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
124 |
Paper tray empty |
[OK] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[ON] |
Embosser will try to resolve the error and resume if it is resolved successfully. |
[OFF] |
Cancel embossing. |
130 |
Service door open |
[OK], [ON] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[OFF] |
Cancel embossing. |
[1] |
Turn off service door sensor and continue printing |
131 |
Paper tray open |
[OK], [ON] |
No Action. |
[OFF] |
Cancel embossing. |
[1] |
Turn off paper tray sensor and continue printing |
132 |
Braille tray open |
[OK] |
Embossing of document is canceled. |
[ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
[1] |
Turn off braille tray sensor and continue printing |
133 |
No tray signal open |
[OK], [ON] |
No Action. |
[OFF] |
Cancel embossing. |
134 |
Braille tray full |
[OK] |
Embossing of document is canceled. |
[ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
[1] |
Turn off braille tray sensor and continue printing |
135 |
Paper jam - release |
[OK] |
Embossing of document is canceled. |
[ON] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[OFF] |
Cancel embossing. |
150 |
No dynamic ip address |
[OK], [ON] |
No action. |
[OFF] |
Cancel embossing. |
200 |
document receiving error |
[OK] |
Continue embossing. |
[ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
201 |
document file empty |
[OK] |
No action. |
[ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
202 |
document unknown esc sequence |
[OK], [ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
203 |
document winBraille file |
[OK] |
Continue embossing. |
[ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
204 |
document xml format |
[OK], [ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
205 |
document html format |
[OK], [ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
206 |
document post script file |
[OK], [ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
210 |
document v3 format |
[OK] |
Embossing of document is cancelled. |
[ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
211 |
document v2 format |
[OK] |
Embossing of document is cancelled. |
[ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
212 |
document min value |
[OK] |
Embossing of document is cancelled. |
[ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
213 |
document max value |
[OK] |
Embossing of document is cancelled. |
[ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
214 |
document max char per line |
[OK] |
Embossing of document is cancelled. |
[ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
215 |
document max lines per page |
[OK] |
Embossing of document is cancelled. |
[ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
216 |
document to many transparent characters |
[OK] |
Embossing of document is cancelled. |
[ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
220 |
document unknown parameter |
[OK], [ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
221 |
document missing parameter |
[OK] |
Cancel embossing. |
[ON] |
Embossing of document is cancelled. |
[OFF] |
Cancel embossing. |
299 |
document formatting error |
[OK] |
Cancel embossing. |
[ON] |
Embossing of document is cancelled. |
[OFF] |
Cancel embossing. |
300 |
upgrade file checksum error |
[OK], [ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
301 |
upgrade file has not a valid magic number |
[OK], [ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
302 |
upgrade file has not a valid header |
[OK], [ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
400 |
undefined hardware setup |
[OK], [ON] |
Reboot embosser. |
[OFF] |
No Action. |
401 |
alignment board not working |
[OK], [ON] |
Shutdown embosser. |
[OFF] |
Continue embossing. |
402 |
release senor not working |
[OK] |
Embossing of document is cancelled. |
[ON] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[OFF] |
Cancel embossing. |
[1] |
Turn off paper release sensor and continue printing |
500 |
undefined software setting |
[OK], [ON] |
Cancel embossing. |
[OFF] |
Cancel embossing. |
501 |
allocate memory error |
[OK], [ON] |
Reboot embosser. |
[OFF] |
Cancel embossing. |
502 |
free memory error |
[OK], [ON] |
Reboot embosser. |
[OFF] |
Cancel embossing. |
503 |
large document error |
[OK], [ON] |
No action. |
[OFF] |
Cancel embossing. |
700 |
Ink timeout |
[OK] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
701 |
Ink startup |
[OK] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
702 |
Ink power up |
[OK], [ON] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
703 |
Ink Power down |
[OK], [ON] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
704 |
Ink postservice |
[OK], [ON] |
Embosser will locate reference point for embosser head(s) and continue embossing. |
[ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
800 |
no sd card available |
[OK], [ON] |
Reboot system. |
[OFF] |
Cancel embossing. |
801 |
sd card is read only - id:0 |
[OK], [ON] |
Embosser will try to reread SD card. |
[OFF] |
Cancel embossing. |
802 |
sd card is read only - id:1 |
[OK], [ON] |
Embosser will try to reread SD card. |
[OFF] |
Cancel embossing. |
803 |
sd card is read only - id:2 |
[OK], [ON] |
Embosser will try to reread SD card. |
[OFF] |
Cancel embossing. |
804 |
no factory settings |
[OK], [ON] |
Shutdown embosser. |
[OFF] |
Cancel embossing. |
810 |
configuration file is corrupt |
[OK], [ON] |
Factory reset of embosser file settings. |
[OFF] |
Cancel embossing. |
811 |
parameter file is corrupt |
[OK], [ON] |
Factory reset of parameter file settings. |
[OFF] |
Cancel embossing. |
812 |
layout file is corrupt |
[OK], [ON] |
Factory reset of layout file settings. |
[OFF] |
Cancel embossing. |
813 |
embosser header file is corrupt |
[OK], [ON] |
Factory reset of embosserhead file settings. |
[OFF] |
Cancel embossing. |
814 |
network file is corrupt |
[OK], [ON] |
Factory reset of network file settings. |
[OFF] |
Cancel embossing. |
900 |
test missing layout file |
[OK], [ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
999 |
restart embosser |
[OK], [ON] |
Reboot embosser. |
[OFF] |
Cancel embossing. |
1000 |
information message |
[OK], [ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
1001 |
save test document |
[OK], [ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
1002 |
format document test failed |
[OK], [ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
1003 |
change paper to |
[OK], [ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |
2000 |
warning message |
[OK], [ON] |
Continue embossing. |
[OFF] |
Cancel embossing. |